Choosing the right chainsaw will require you to consider your minimum and maximum workload and decide which type you’ll need to get the job done.
The chainsaw is one of the most important and straightforward power tools you can own. A chainsaw is a dangerous tool and you must know how to use a chainsaw when working.
However, they belong to the most dangerous devices if we do not know how to use them properly. They are large, loud but often they are also the best tool for fast and accurate work.
Chainsaws are the perfect tool for cutting up fallen trees and large branches. We made a chain saw expert guideline to walk us through the process of using a chainsaw for beginners.
How To Choose And Use A Chainsaw Step-By-Step
This is a little unnerving at first because the saw pushes toward you. The saw pulls slightly and is easy to control by maintaining a firm grip.
But it’s safe as long as you’re well braced and follow all other precautions. Cutting with the chain on the bottom of the bar is the most common and natural-feeling way to cut.
Cutting from the underside of a branch requires you to cut with the top of the bar. However, there’s one spot on the bar that you should carefully avoid.
This spot, called the kickback zone, is the top half of the bar’s tip. That’s why modern chainsaws are equipped with a chain brake designed to stop the chain if a kickback occurs.
If the kickback zone comes in contact with something while the chain is moving, the saw will kick up and back toward you.
Get a feel for how your saw responds to the throttle. Cut only when you are in a comfortable, well-balanced position with your feet about shoulder-width apart.
Stand to one side of the saw, never directly or behind it. You’ll feel different forces when cutting. When cutting with the bottom of the bar, the saw will pull you into the work.
When cutting with the top of the bar (undercutting), the saw will tend to push you away from the work. This second force is called a pushing chain.
When cutting with a pushing chain, brace the back handle of the saw or your arm against your thigh to gain more control of the saw and reduce fatigue.
To start the saw, engage the chain brake, turn on the ignition switch, pull out the choke (for a cold engine) and lock on the fast idle.
With the saw sitting on the ground, put the toe of your right boot into the back handle loop and grasp the front handle with a stiff left arm.
Pull the starter handle to fire up the engine. Push in the choke and take it off fast idle, then pull the chain brake back towards the front handle to release the chain brake for cutting.
-
Adjusting Chain Tension
To make adjustments, loosen the bar nuts that hold the bar.
The tension is correct when you can’t lift the chain drivers free of the bar groove but you can still drag the chain easily around the bar with a gloved hand.
Then lift the bar while tightening the adjusting screw until the chain is snug against the bar. Retighten the bar nut.
Loose chains can fly off the bar, causing serious injury. A loose chain also damages the drivers BAR on the chain and prevents them from fitting back into the bar groove.
Before starting, check the chain tension. Recheck it after every hour or so of use, and adjust it if necessary. New chains stretch and need to be checked after 20 minutes of use.
How To Use A Chainsaw To Trim The Hedge?
Due to the dangerous nature of power equipment, you must follow proper safety procedures during use.
Chain saws are versatile pieces of power equipment that can make yard work much more efficient than manual trimmers.
Chainsaws are versatile pieces of power equipment that can make yard work much more efficient than manual trimmers.
The best time to prune lilac bushes is right after their flowering has stopped. Pruning too early or too late can kill new buds and inhibit future growth.
The technique used to operate your chain saw depends in part on the plant you are cutting.
For instance, to cut juniper bushes, you will need to exercise extreme caution and precision to cut only old, weak or crossed branches.
When trimming lilac bushes, always wait until the plants have reached at least 6 feet in height.
Cutting the entire stem, rather than just pruning small pieces or overgrown branches, is ideal.
You can trim leaf-bearing hedges with a chainsaw. You should begin pruning these at an early age to encourage healthy growth.
Hedge trimmers can offer a greater level of accuracy for this sort of project than can a chainsaw. You should prune juniper bushes in early spring for best results.
Try to cut deciduous hedges in the late summertime, if possible. Take care to avoid nesting birds when using your chainsaw to prune hedges.
Related Post